|Xikou,Fenghua,Zhejiang Province, Chinaemail@example.com|
|Place of Origin:||China|
|Minimum Order Quantity:||1 piece|
|Packaging Details:||Plastic bags,Boxes, Cartons, Pallets,or according to customer's requirement|
|Delivery Time:||within 1-7 working days after payment|
|Payment Terms:||T/T , Western Union|
|Supply Ability:||1000 pcs|
|Working Temperature:||-10 °C To +80 °C||Proof Pressure:||1.5MPa|
pneumatic actuator cylinder,
smc pneumatic cylinder
SMC Compact rotary table MSAQB10A Pneumatic Cylinder Rack Pinion Style
Ordering Code: MSQB10A, Any other types please contact freely.
1) TN series are alll with magnet
2) When the thread is standard, the code is blank
|With adjustment bolt||1 Mpa|
|With internal shock absorber||0.6 Mpa (Note 1)|
|Basic type||0.1 Mpa|
|High precision type||0.2 Mpa||0.1 Mpa|
|Ambient and fluid temperature||0 to 60 ℃ (with no freezing)|
|Cushion||With adjustment bolt||Rubber bumper|
|With internal shock absorber||Shock absorber|
|Shock absorber model||RBA0805
|Angle adjustment range||0 to 190° (note 2)|
|Cylinder bore size||ø15||ø18||ø21||ø25||ø28||ø32||ø40|
|Port size||End ports||M5 x 0.8||Rc 1/8|
|Side ports||M5 x 0.8|
1.Enterprises standard is implemented.
2.Embeded installation and fixation mode saves the installation space.
3.It is good resistance to bending and twisting moments.
4. Mounting holes on three sides facilitates multi-position mounting.
5.Bumper in front of the barrel can adjust the stroke of cylinder and relieve impact.
6.Standard configuration of this series has magnet and the type without magnet is not available.
|Basic type||With adjustment bolt||530||990||1290||2080||2880||4090||7580|
|With internal shock absorber||540||990||1290||2100||2890||4100||7650|
|High precision type||With adjustment bolt||560||1090||1410||2240||—|
|With internal shock absorber||570||1090||1410||2260|
Rotation Direction and Rotation Angle
1. The rotary table turns in the clockwise direction where the A port is pressurized, and in the counterclockwise direction when the B port is pressurized.
2. By adjusting the adjustment bolt, the rotation end can be set within the ranges shown in the drawing for the desired rotation angle.
3. The rotation angle can also be set on a type with internal absorber.
With adjust bolt, internal shock absorber
|Size||Adjustment angle per rotation of
angle adjustment screw
1. The drawing shows the rotation range of the positioning pin hole.
2. The pin hole position in the drawing shows the counterclockwise
rotation end when the adjustment bolts A and B are tightened
equally and the rotation is adjusted 180°.
Rotation Range Example
1. Various rotation ranges are possible as shown in the drawings below using adjustment bolts A and B.
(The drawings also show the rotation ranges of the positioning pin hole.)
2. The rotation angle can also be set on a type with inertial absorber.
1.When load changes in the work, the cylinder with abundant output capacity shall be ed.
2.The medium used by cylinder shall be filtered to 40μm or below.
3.Necessary protection measure shall be taken in the environment with higher humidity, much dust or water drops, oil dust and welding dregs.
4.Dirty substances in the pipe must be eliminated before cylinder is connected with pipeline to prevent the entrance of particles into the cylinder.
5.As both the front cover and piston are short, too large stroke can not be ed.
6.Relative cylinder with high temperature resistance or corrosion resistance shall be chosen under the condition of high temperature or corrosion.
7.The cylinder shall avoid redial load in operation to maintain the normal and extend service life.
8.Anti-freezing measure shall be adopted under low temperature environment to prevent moisture freezing.
9.If the cylinder is dismantled and stored for a long time, please conduct anti-rust treatment to the surface. Anti-dust cap shall be ed into the inlet and outlet ports. As the precision of the manufacture and guide is high, Please do not dismantle the fixed block or cylinder cover.
1. If the products we have in store, we will send it out ASAP after payment.
2. If the products which were customized, we will complete the production within a specified period of time, and send it out the first time, we can promise it.
3. Also we can send by your delivery acount if you want.
4. We have a variety of ways to send goods, usually DHL, Fedex, TNL will be normal ways. If you require use of a courier, we can do it.
Products Shopping Guide
For example: you want to purchase a batch of cylinders but you don't know which type you are really want, so you can tell me all your requirement and I'll recommend to you.
We can provide a series of after-sale service, such as product introduction, mounting, debugging, technical support and so on.
|Our product features||Our Services Guarantee:|
|1) Competitive price||1) Prompt respond (Reply with 24 hours)|
|2) Good quality||2) Free Samples (Customer pay for the delivery cost)|
|3) Professional Packaging||3) Registration support.|
|4) Produce according to Customers’ instruction||4) Photos/videos are available during production.|
|5) None delay shipment||5) Loading inspection, and send loading photos before shipment.|
All item Comes with Basic 3 Month Sellers Warranty, if item defective in 3 Month, We will offer replacement without extra Charger(including shipping fee)After we Receive the Defective item.
If item Defective after 3 Month, Buyers can still send it back, We will contact suppliers or Manufactory for Warranty. Buyers Might Need to pay the Shipping fee For resend the replaced item.